Beijer-electronics QTERM®-A12 Manuel d'utilisateur

QTERM®-A12 TERMINALHARDWARE MANUALBEIJER ELECTRONICS2212 South West Temple #50Salt Lake City, Utah 84115-2648USAPhone 801-466-8770Fax 801-466-8792Emai

Safety Summary4 QTERM-A12 TerminalNotes

QTERM-A12 Terminal 5CHAPTER 3APPLYING POWERPower is supplied to the QTERM-A12 terminal via the COM1 serial port connector or the 3-pin power terminal

Primary Serial Port Connector for Power Input Applying Power6 QTERM-A12 Terminallation between signal common and earth ground, care must be taken when

Applying Power Optional Power-over-Ethernet Interface QTERM-A12 Terminal 73.4 Optional Power-over-Ethernet InterfaceThe QTERM-A12 may be equipped with

Powering On the Terminal for the First Time Applying Power8 QTERM-A12 Terminal3.5 Powering On the Terminal for the First TimeWhen you connect power to

QTERM-A12 Terminal 9CHAPTER 4HARDWARE DESCRIPTION AND ARCHITECTURE4.1 User InterfaceDisplayThe QTERM-A12 features a TFT color SVGA (800 x 600 pixels)

Serial Communications Hardware Description and Architecture10 QTERM-A12 Terminal4.4 Serial CommunicationsThe QTERM-A12 has two serial ports, designate

Hardware Description and Architecture Power Supply QTERM-A12 Terminal 114.7 Power SupplyThe QTERM-A12 has a 10- to 32-volt DC input range and can be p

Housing Hardware Description and Architecture12 QTERM-A12 TerminalNotes

QTERM-A12 Terminal 13CHAPTER 5INSTALLATIONA QTERM-A12 terminal uses a rugged chemical resistant polymer housing and mounting components. When properl

Copyright © 2011 Beijer Electronics. Printed in the USA. All rights reserved. No part of this publication may be reproduced, in any form or by any mea

Cutting Out for Panel Mount Installation14 QTERM-A12 Terminal5.1 Cutting Out for Panel Mount5.1.1 Standard Version CutoutThe standard version cutout i

Installation Cutting Out for Panel Mount QTERM-A12 Terminal 155.1.2 Modular Version CutoutThe modular version cutout is to be used with QTERM-A12 mode

Installing the Terminal Installation16 QTERM-A12 Terminal5.2 Installing the TerminalNOTE ☞Use of an anti-static strap is recommended when performing i

Installation Installing the Terminal QTERM-A12 Terminal 17• PortraitWhen looking at the front of the unit, the back panel serial port(s) should be fac

Installing the Terminal Installation18 QTERM-A12 Terminalthe back panel may indicate the orientation. If not, you can determine which side should be a

QTERM-A12 Terminal 19CHAPTER 6SPECIFICATIONS DISPLAYColorTFT color SVGA LCD display65,536 colorsSize308 mm (12.1") diagonal246 mm x 184.5 mm

Specifications20 QTERM-A12 Terminal PHYSICALSTANDARD VERSION (WITH FACTORY-INSTALLED BEZEL)Dimensions 344.4 (W) x 267.0 (H) x 69.1 (D) mmMass 2.05 k

Specifications QTERM-A12 Terminal 21MEMORYDDR SDRAM128 Mbytes standard, 16 bit wide bus, 130 Mhz => 520 Mbytes/s transfer rateNon-volatile storage

Specifications22 QTERM-A12 TerminalNotes

QTERM-A12 Terminal 23CHAPTER 7MECHANICAL7.1 Layout and Dimensions7.1.1 Standard VersionThe standard version of the QTERM-A12 is equipped with a facto

FCC Compliance InformationThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

Layout and Dimensions Mechanical24 QTERM-A12 Terminal Figure 6QTERM-A12 Back View (units: mm) Figure 7QTERM-A12 Bottom View (units: mm)

Mechanical Layout and Dimensions QTERM-A12 Terminal 25 Figure 8QTERM-A12 Side View (units: mm)

Layout and Dimensions Mechanical26 QTERM-A12 Terminal7.1.2 Modular VersionThe modular version of the QTERM-A12 does NOT have a front bezel. Mounting s

Mechanical Layout and Dimensions QTERM-A12 Terminal 27 Figure 11Modular QTERM-A12 Bottom View (units: mm) Figure 12Modular QTERM-A12 Side View (units:

Connector Pinouts Mechanical28 QTERM-A12 Terminal7.2 Connector Pinouts7.2.1 Primary Serial PortThe following table shows the pinouts for each type of

Mechanical Connector Pinouts QTERM-A12 Terminal 297.2.2 Secondary Serial PortThe secondary serial port on the QTERM-A12 is configured as EIA-232 only

Connector Pinouts Mechanical30 QTERM-A12 Terminal7.2.4 Ethernet PortThe Ethernet port has a standard 10/100Base-T interface with an 8-pin (RJ-45) modu

Mechanical Connector Pinouts QTERM-A12 Terminal 317.2.5 USB 2.0 PortsThe QTERM-A12 includes two USB 2.0 full-speed ports. The connector orientation an

Connector Pinouts Mechanical32 QTERM-A12 TerminalNotes

Notes

QTERM-A12 Terminal iCONTENTSCHAPTER 1. INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ContentsiiQTERM-A12 TerminalNotes

QTERM-A12 Terminal 1CHAPTER 1INTRODUCTIONThe QTERM®-A12 is a rugged graphic human-machine interface terminal for use in a wide range of commercial an

Introduction2 QTERM-A12 TerminalNotes

QTERM-A12 Terminal 3CHAPTER 2SAFETY SUMMARYThe QTERM-A12 terminal is certified to operate at Temperature Code T6 in a Class I, Division 2, Group A, B